Форум программистов [Powered by Invision Power Board]

Код

[EciAdsl 1/5] Setting up USB support...

Preliminary USB device filesystem is OK

[EciAdsl 2/5] Uploading firmware...

Process skipped .. no more needed
firmware loaded successfully

[EciAdsl 3/5] Synchronization...

ERROR eciadsl-synch SYNCHING: failed
ERROR eciadsl-synch: failed 
Synchronization successful

[EciAdsl 4/5] Connecting to provider...

Connection successful

[EciAdsl 5/5] Setting up route table...

Waiting for tap0...

Код

connect: Network is unreachable

Код

VID1=0915
PID1=8104
VID2=0915
PID2=8104
MODE=LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS
VCI=35
VPI=0
FIRMWARE=/etc/eciadsl/firmware00.bin
SYNCH=/etc/eciadsl/gs7470_synch06.bin
USE_DHCP=yes
USE_STATICIP=no
MODEM_CHIPSET=GS7470
SYNCH_ALTIFACE=1
PPPOECI_ALTIFACE=4
PROVIDER=Other
PPPD_USER=ptn
PPPD_PASSWD=
MODEM=D-Link DSL200
DNS1=213.158.0.3
DNS2=213.158.0.3
STATICIP=
GATEWAY=

Код

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:35 errors:0 dropped:0 overruns:0 frame:0
          TX packets:35 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:11272 (11.0 KiB)  TX bytes:11272 (11.0 KiB)

Код

You are using linux kernel version 2.6.18-3-686
Support for USB is OK
Preliminary USB device filesystem is OK
dabusb module is not loaded: OK
UHCI support is OK
OHCI support is not needed
/dev/ppp is OK
HDLC support is OK
HDLC support is OK (no bug)
Loading EZ-USB firmware...
Process skipped .. no more needed
Loading the GlobeSpan firmware...
ERROR can't set configuration 1
ERROR eciadsl-synch: failed 
You are using pppd version 2.4.3 (untested)
You have an /etc/ppp/options file. Options in this file may conflict with
options from /etc/ppp/peers/adsl. We suggest to remove this file or make a
backup copy.
No existing PPP connection... trying to make one (please wait)
Couldn't get channel number: Input/output error
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24781), status = 0x0
Couldn't get channel number: Input/output error
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24791), status = 0x0
Couldn't get channel number: Input/output error
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24801), status = 0x0
Couldn't get channel number: Input/output error
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24811), status = 0x0
using channel 12
Using interface ppp0
Connect: ppp0 <--> /dev/pts/3
Modem hangup
Connection terminated.
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24821), status = 0x0
using channel 13
Using interface ppp0
Connect: ppp0 <--> /dev/pts/4
Modem hangup
Connection terminated.
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24837), status = 0x0
using channel 14
Using interface ppp0
Connect: ppp0 <--> /dev/pts/5
Modem hangup
Connection terminated.
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24853), status = 0x0
using channel 15
Using interface ppp0
Connect: ppp0 <--> /dev/pts/6
Modem hangup
Connection terminated.
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24869), status = 0x0
using channel 16
Using interface ppp0
Connect: ppp0 <--> /dev/pts/7
Modem hangup
Connection terminated.
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24885), status = 0x0
using channel 17
Using interface ppp0
Connect: ppp0 <--> /dev/pts/8
Modem hangup
Connection terminated.
Script /usr/bin/eciadsl-pppoeci -vpi 0 -vci 35 -vendor 0x0915 -product 0x8104 -mode LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS finished (pid 24901), status = 0x0
PPP: very bad ... usermode driver just crashed
tail: Warning: "+number" syntax is deprecated, please use "-n +number"

Цитата

Все же решила попробовать помучать свой Дебиан по части подключения к ADSL-Авангард с помощью D-Link DSL-200

Код


SYNCH_ALTIFACE=1
PPPOECI_ALTIFACE=4

Цитата

отредактируй...и расскажи как получилось.

Код


Using interface ppp0
Connect: ppp0 <--> /dev/pts/1
LCP: timeout sending Config-Requests
Connection terminated.
Modem hangup
pppoe: Timeout waiting for PADO packets
Using interface ppp0
Connect: ppp0 <--> /dev/pts/1
LCP: timeout sending Config-Requests
Connection terminated.
Modem hangup
pppoe: Timeout waiting for PADO packets
Using interface ppp0
Connect: ppp0 <--> /dev/pts/1
LCP: timeout sending Config-Requests
Connection terminated.
Modem hangup

Код


#***********************************************************************
#
# pppoe.conf
#
# Configuration file for rp-pppoe.  Edit as appropriate and install in
# /etc/ppp/pppoe.conf
#
# NOTE: This file is used by the pppoe-start, pppoe-stop, pppoe-connect and
#       pppoe-status shell scripts.  It is *not* used in any way by the
#       "pppoe" executable.
#
# Copyright (C) 2000 Roaring Penguin Software Inc.
#
# This file may be distributed under the terms of the GNU General
# Public License.
#
# LIC: GPL
# $Id: pppoe.conf,v 1.11 2005/08/09 02:49:12 dfs Exp $
#***********************************************************************

# When you configure a variable, DO NOT leave spaces around the "=" sign.

# Ethernet card connected to DSL modem
ETH='tap0'

# PPPoE user name.  You may have to supply "@provider.com"  Sympatico
# users in Canada do need to include "@sympatico.ca"
# Sympatico uses PAP authentication.  Make sure /etc/ppp/pap-secrets
# contains the right username/password combination.
# For Magma, use xxyyzz@magma.ca
USER='ptn'

# Bring link up on demand?  Default is to leave link up all the time.
# If you want the link to come up on demand, set DEMAND to a number indicating
# the idle time after which the link is brought down.
DEMAND=no
#DEMAND=300

# DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2;
# NOCHANGE=do not adjust.
DNSTYPE=SPECIFY

# Obtain DNS server addresses from the peer (recent versions of pppd only)
# In old config files, this used to be called USEPEERDNS.  Changed to
# PEERDNS for better Red Hat compatibility
PEERDNS=no

DNS1=82.138.20.130
DNS2=82.138.29.29

# Make the PPPoE connection your default route.  Set to
# DEFAULTROUTE=no if you don't want this.
DEFAULTROUTE=yes

### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU'RE AN EXPERT

# How long pppoe-start waits for a new PPP interface to appear before
# concluding something went wrong.  If you use 0, then pppoe-start
# exits immediately with a successful status and does not wait for the
# link to come up.  Time is in seconds.
#
# WARNING WARNING WARNING:
#
# If you are using rp-pppoe on a physically-inaccessible host, set
# CONNECT_TIMEOUT to 0.  This makes SURE that the machine keeps trying
# to connect forever after pppoe-start is called.  Otherwise, it will
# give out after CONNECT_TIMEOUT seconds and will not attempt to
# connect again, making it impossible to reach.
CONNECT_TIMEOUT=30

# How often in seconds pppoe-start polls to check if link is up
CONNECT_POLL=2

# Specific desired AC Name
ACNAME=

# Specific desired service name
SERVICENAME=

# Character to echo at each poll.  Use PING="" if you don't want
# anything echoed
PING="."

# File where the pppoe-connect script writes its process-ID.
# Three files are actually used:
#   $PIDFILE       contains PID of pppoe-connect script
#   $PIDFILE.pppoe contains PID of pppoe process
#   $PIDFILE.pppd  contains PID of pppd process
CF_BASE=`basename $CONFIG`
PIDFILE="/var/run/$CF_BASE-pppoe.pid"

# Do you want to use synchronous PPP?  "yes" or "no".  "yes" is much
# easier on CPU usage, but may not work for you.  It is safer to use
# "no", but you may want to experiment with "yes".  "yes" is generally
# safe on Linux machines with the n_hdlc line discipline; unsafe on others.
SYNCHRONOUS=no

# Do you want to clamp the MSS?  Here's how to decide:
# - If you have only a SINGLE computer connected to the DSL modem, choose
#   "no".
# - If you have a computer acting as a gateway for a LAN, choose "1412".
#   The setting of 1412 is safe for either setup, but uses slightly more
#   CPU power.
CLAMPMSS=1412
#CLAMPMSS=no

# LCP echo interval and failure count.
LCP_INTERVAL=20
LCP_FAILURE=3

# PPPOE_TIMEOUT should be about 4*LCP_INTERVAL
PPPOE_TIMEOUT=80

# Firewalling: One of NONE, STANDALONE or MASQUERADE
FIREWALL=NONE

# Linux kernel-mode plugin for pppd.  If you want to try the kernel-mode
# plugin, use LINUX_PLUGIN=/etc/ppp/plugins/rp-pppoe.so
LINUX_PLUGIN=

# Any extra arguments to pass to pppoe.  Normally, use a blank string
# like this:
PPPOE_EXTRA=""

# Rumour has it that "Citizen's Communications" with a 3Com
# HomeConnect DSL Modem DualLink requires these extra options:
# PPPOE_EXTRA="-f 3c12:3c13 -S ISP"

# Any extra arguments to pass to pppd.  Normally, use a blank string
# like this:
PPPD_EXTRA=""


########## DON'T CHANGE BELOW UNLESS YOU KNOW WHAT YOU ARE DOING
# If you wish to COMPLETELY overrride the pppd invocation:
# Example:
# OVERRIDE_PPPD_COMMAND="pppd call dsl"

# If you want pppoe-connect to exit when connection drops:
# RETRY_ON_FAILURE=no

Цитата

Почитаю-ка я доки по rp-pppoe

Цитата

через пять минут модем сам оборвал связь и больше коннектиться н хотел