Модераторы: Mazzi
  

Поиск:

Ответ в темуСоздание новой темы Создание опроса
> Hydraulic motor disassembly steps 
:(
    Опции темы
wyd1014
Дата 3.7.2020, 13:42 (ссылка) | (нет голосов) Загрузка ... Загрузка ... Быстрая цитата Цитата


Новичок



Профиль
Группа: Участник
Сообщений: 2
Регистрация: 3.7.2020

Репутация: нет
Всего: нет



Hydraulic motor disassembly steps
The clearance of each moving pair of hydraulic motor from the factory has been well matched, and the user is not allowed to change parts casually. In general, do not open the motor at will, only in the case of serious failure, we need to agree with the company to open the inspection.
(1) Preparation before opening

  Remove the drain plug and drain the oil from the motor housing.

  Loosen 5 screws on the pan and remove the pan.

  Take out the oil distribution pan, positioning ring, pad, cylindrical pin and double-headed key.

  Note: In order to prevent the change of backward rotation in the reassembly, the marks of the same square shall be made on the end face of the output shaft and the oil distribution plate surface.
(2) Sequence of disassembly and installation

  Remove the cover, screw the clean screw into the center screw hole of the crankshaft, and lift out the crankshaft.

  Remove the clamping ring on the connecting rod.

  3. Take out the connecting rod components of the plunger body, and make corresponding marks one by one, so as to ensure the original assembly clearance during reassembly. If necessary, the combination of the plunger body and connecting rod can be decomposed again: loosen the hole with the spring retaining ring, take out the retaining ring, and the plunger body and connecting rod can be separated.

  4. Assemble according to the opposite procedure above, and pay attention to ensure the axial clearance of the bearing.

  All parts must be cleaned before assembly to prevent scratch or scratch any working surface.

  If there is only oil leakage in the sand hole of the plunger sleeve or oil leakage in the joint surface of the plunger sleeve and the shell, loosen the screws on the plunger sleeve, remove the plunger sleeve, and replace the plunger sleeve or "O" ring.
Related products:
Ultrafiltration System For Water Purification
Fully Automatic Water Softener


Other related products:
Vacuum pump price list

  Basic vacuum pump selection

  Vacuum pump selection

  Vacuum pumps types of industrial





PM MAIL WWW   Вверх
rossye
Дата 8.9.2022, 18:57 (ссылка) | (нет голосов) Загрузка ... Загрузка ... Быстрая цитата Цитата


Новичок



Профиль
Группа: Участник
Сообщений: 4
Регистрация: 7.9.2022

Репутация: нет
Всего: нет



вввв
PM MAIL   Вверх
  
Ответ в темуСоздание новой темы Создание опроса
1 Пользователей читают эту тему (1 Гостей и 0 Скрытых Пользователей)
0 Пользователей:
« Предыдущая тема | Разное (электроника) | Следующая тема »


 




[ Время генерации скрипта: 0.0881 ]   [ Использовано запросов: 20 ]   [ GZIP включён ]


Реклама на сайте     Информационное спонсорство

 
По вопросам размещения рекламы пишите на vladimir(sobaka)vingrad.ru
Отказ от ответственности     Powered by Invision Power Board(R) 1.3 © 2003  IPS, Inc.