Люди, нужна помощь. Мне нужно, чтобы при изменении положения TTrackBar изменялась громкость звуков в системе. Или хотя-бы, чтобы при нажатии на кнопку звук выключался, а при повторном нажатии включался.
Заранее спасибо!

MMRESULT auxSetVolume(UINT uDeviceID, DWORD dwVolume);



Sets the volume of the specified auxiliary output device.

· Returns MMSYSERR_NOERROR if successful or an error otherwise. Possible error values include the following:

MMSYSERR_BADDEVICEID Specified device identifier is out of range.
uDeviceID

Identifier of the auxiliary output device to be queried. Device identifiers are determined implicitly from the number of devices present in the system. Device identifier values range from zero to one less than the number of devices present. Use the auxGetNumDevs function to determine the number of auxiliary devices in the system.

dwVolume

Specifies the new volume setting. The low-order word specifies the left-channel volume setting, and the high-order word specifies the right-channel setting. A value of 0xFFFF represents full volume, and a value of 0x0000 is silence.
If a device does not support both left and right volume control, the low-order word of dwVolume specifies the volume level, and the high-order word is ignored.

Not all devices support volume control. To determine whether the device supports volume control, use the AUXCAPS_VOLUME flag to test the dwSupport member of the AUXCAPS structure (filled by the auxGetDevCaps function).
To determine whether the device supports volume control on both the left and right channels, use the AUXCAPS_LRVOLUME flag to test the dwSupport member of the AUXCAPS structure (filled by auxGetDevCaps).

Most devices do not support the full 16 bits of volume-level control and will use only the high-order bits of the requested volume setting. For example, for a device that supports 4 bits of volume control, requested volume level values of 0x4000, 0x4FFF, and 0x43BE will produce the same physical volume setting, 0x4000. The auxGetVolume function will return the full 16-bit setting set with auxSetVolume.
Volume settings are interpreted logarithmically. This means the perceived volume increase is the same when increasing the volume level from 0x5000 to 0x6000 as it is from 0x4000 to 0x5000.


he auxGetVolume function retrieves the current volume setting of the specified auxiliary output device.

MMRESULT auxGetVolume(

   UINT uDeviceID,
   LPDWORD lpdwVolume
  );


Parameters

uDeviceID

Identifier of the auxiliary output device to be queried.

lpdwVolume

Address of a variable to be filled with the current volume setting. The low-order word of this location contains the left channel volume setting, and the high-order word contains the right channel setting. A value of 0xFFFF represents full volume, and a value of 0x0000 is silence.
If a device does not support both left and right volume control, the low-order word of the specified location contains the volume level.
The full 16-bit setting(s) set with the auxSetVolume function are returned, regardless of whether the device supports the full 16 bits of volume-level control.



Return Values

Returns MMSYSERR_NOERROR if successful or an error otherwise. Possible error values include the following:

MMSYSERR_BADDEVICEID Specified device identifier is out of range.


Remarks

Not all devices support volume control. To determine whether a device supports volume control, use the AUXCAPS_VOLUME flag to test the dwSupport member of the AUXCAPS structure (filled by the auxGetDevCaps function).
To determine whether a device supports volume control on both the left and right channels, use the AUXCAPS_LRVOLUME flag to test the dwSupport member of the AUXCAPS structure (filled by auxGetDevCaps).

Все юзай!

А при чём тут AUX ?
WaveOutSetVolume() нужен

Не, я в английском ни чего не понимаю!  

УРА!!!!!! ПОЛУЧИЛОСЬ!!!! Я НАШЕЛ VCL ДЛЯ РАБОТЫ CО ЗВУКОМ!!! ВСЕМ СПАИСБО!!! БОЛЬШЕ ВАША ПОМОЩЬ НЕ ТРЕБУЕТСЯ!!!